Latex Rubber Extreme Full Coverage

Ben Esra telefonda seni boşaltmamı ister misin?
Telefon Numaram: 00237 8000 92 32

Brunette

Latex Rubber Extreme Full CoverageThis is not so much a story as it is a description of a full coverage latex catsuit that I once made. I thought that you people who have a latex fetish, as I do, and just can’t seem to get enough, might find it interesting.I am gay, a Bottom and have a steady Boyfriend. I have only had a couple long term relationships where we progressed to the point of ditching the condoms and going bareback. This is about a suit that I made during one of those past relationships with a rubber loving partner.I love wearing full coverage latex catsuits, on their own, or under other rubber clothing. I shave my entire body and love the latex, and only latex, in contact with every inch of my skin. I like to have no skin to skin contact of any of my body parts, and no zippers interrupting that contact. I like it to be very supple, stretchy, non binding and yet skin tight so I usually make make my suits of about 2mm, (.008 inch) thick latex. Although not the suit I am writing about, you can see a regular suit of this thin material in one of my profile pictures. It’s the one I am wearing while laying on my back on the green bed spread.I started with some .2mm transparent latex from MJ Trends. I made a classic hooded, gloved and footed face entry catsuit. The face opening goes from above the eyes to below the chin. The feet and gloves are attached and the suit is pulled on through the face opening and there are no zippers hakkari rus escort on the suit.The transparent gloves and attached cock and ball sheath were the ones listed as thin from Twist My Rubber Arm and are only .25mm thick, not quite twice as thick as a surgical glove. The feet were transparent latex toe socks that are much, much thinner than most and are sometimes listed on Ebay. Once in the suit, I would wear it for hours and hours. I made a very small hole in the tip of the sheath so I can use the bathroom while still completely in the suitI wanted to be a complete rubber being, be able to do every thing and still be completely and totally rubbered up. My suit design has a diamond shaped crotch panel that, when the suit is on and stretched tight over the body, allows the crotch to pull up snug into the crack of the ass so even my butt cheeks don’t contact each other. I usually just make a small slit opening so I can be fucked. The stretch of the suit pulls the edges together and since it is up in my crack, can’t be felt as an opening or seen unless I bend over and pull my cheeks apart. However, this suit I wanted as total rubber and even my holes rubbered, but I didn’t want an internal anal sheath.What I did was make a short internal sheath to attach to the suit. Again, it was a very thin material, only a little over an inch in diameter. Being thin, it was big enough to stretch over hakkari rus escort bayan my Buddy’s cock and yet small enough that it didn’t really bunch up where it entered my hole. It was about 3 inches long and tapered to about 2 1/2 inches in diameter at the inner open end. I bought two thick rubber “O” rings, stacked them and painted with several layers of liquid latex making a semi rigid short tube. I stretched the open end of the anal sheath over the tube, folded it inward and glued it together. After the suit is on I can lube it up and the sheath is just long enough that I can squeeze the ring flat, turn one edge toward my hole and slip it in. Once in, it snaps open. It pulls up snug against the inside of my ass ring and keeps the suit pulled up snug against my hole. I always use an anal lube syringe to inject silicone anal lube into myself and it kept the latex slick enough for my Buddy’s cock to slide freely through the sheath as he fucked me. The latex, being thin, was virtually unnoticeable while being fucked. Also, being open ended, I had a completely rubbered hole and still got to have his load actually inside me when he came.To finish the suit, I needed to remedy the open face and chin situation. I made another thin full face hood with just eye, mouth and nostril openings. I made a mold of the in and outside of my lips using alginate from Smooth-On, (the stuff the Dentist rus escort hakkari uses to make a cast for a crown). Picture a sort of oval hallow doughnut with the outside of the ring removed. From this I made one of plaster and painted it with glossy paint. I used the mold for liquid latex and made lips to attach to the hood. They curved around to the inside to where my lips connect to my gums. It made me talk funny and the latex turns a little white inside the mouth after a while because of the moisture, but it doesn’t harm the latex and it turns back again after drying. More importantly, my mouth was now rubberized, I could still drink, take and suck cock or tongue. Last of all, I used the same method to cast the inside of my nostrils and added these to the nose of the hood. I pull the suit on and, before pulling the hood of the suit in place, put on the hood with the lips and nostril openings to have a total rubber skin with no zips, even my body openings rubberized and still have normal body functions and unprotected sex with my Rubber Buddy! The only thing not rubberized were the eye openings. I thought about attaching mirrored sun glass lenses, as I did to the red suit in my pictures, but I never solved the problem of them fogging up as they did on that suit.Alas, as pull on suits tend to do more quickly, it wore out too much to repair. It was a total thrill to wear and would have lasted much longer if I had reserved it just for sex, but I couldn’t help myself and wore it often when only by myself. I was well worth the time and effort though and I swallowed many juicy loads and took even more up the butt while wearing that suit.I have been thinking of making another in transparent red, but haven’t found the gloves and toe socks in that color yet.Riki

Ben Esra telefonda seni boşaltmamı ister misin?
Telefon Numaram: 00237 8000 92 32

Bir cevap yazın

E-posta hesabınız yayımlanmayacak. Gerekli alanlar * ile işaretlenmişlerdir